Designed by
the Angler,
for the Angler.

Fishing lures designed through engineering, 3D printing and the experience of anglers themselves. Choose your design, customise it and make it your own.

Fully customisableSize, weight, colour and more
Engineered designsCAD-modelled, tested before release
Sustainable materialsIncluding recycled plastics
Angler collaborationYour ideas. Real products.
Home›Design Your Lure›Crankbait
60 mm
25 mm
Drag to rotate · Scroll or pinch to zoom

Live Specifications (estimated)

Length—
Weight—
Diving Depth—
Buoyancy—
Hooks—

Customise Your LureCrankbait

Tell us what you're fishing for and today's conditions. We'll suggest three lures, and the Swim Lab checks each one reaches the depth the fish are holding at.

Target fish
Water clarity

Quick test: lower a white lure 30 cm. Still clear to see means clear; just visible means stained; gone means muddy.

Weather
Light
Wind
0.5 m8 m
Body profile real fish proportions
mm
Body width 100%
SlimmerStandardWider
Fins flexible TPU · +£1.50 each
Colour for all fins
Build details wall and print material
Wall thickness thicker walls add strength and weight
Body material

Scaling never stretches the model. The wall stays the same, hooks step up a size as the body grows, and tungsten plus internal lattice are re-sized to hit your buoyancy target.

Diving lip (estimated)
Fine-tune lip width and line tie
At the noseToward the lip tip

Flatter, longer lips dive deeper; steeper lips run shallower with more wiggle. Angle is measured down from the body line. You can also drag the lip tip in Shape Studio.

Fishing in
Float or sink fresh water
Weight & balance

Rattle
Smart Tag NFC · +£1.00

How Smart Tags earn you 20%
Hooks
Hook finish
Through-wire
Cutting list
Colour pattern

Finish
Depth card how deep it runs by cast length and line
£0
posted in 5–7 days

Made to order in Derry · demo pricing

Swim Lab

Every change, re-simulated.

Retrieve, action, trim and cast are recalculated from your design each time you change anything. Numbers are model predictions for a 3D-printed body. Tank-test before you trust them.

Test conditions
Retrieve profile
Action from above
Running trim and forces
Cast
Why it swims like this
    Change logwhat each edit did
      The science behind the numbersrules the simulator uses, and where they come from
      • Lip lift and stall. The lip is treated as a short, flat plate. Lift rises with angle until it stalls; stubby lips stall later. Checked against flume tests on crankbait lips. Daida et al. 2002, lip aspect ratio
      • Checked against real lures. A 120 mm minnow runs 1.4 m with the shallow lip and 1.9 m with the medium lip. Rapala list 1.2–1.8 m for the 11–13 cm Original Floater and 1.2–2.4 m for the X-Rap 12. Rapala Original Floater · Rapala X-Rap
      • Conditions planner. Water temperature sets how hard fish chase. Clarity sets colour and noise: natural and silent in clear water, contrast and rattles when stained, dark and loud in mud. Wind colours the water up, and after a cold front you go smaller, slower and about a metre deeper. LureLogic clarity guide · LureLogic cold fronts
      • Lip angle vs depth. Flatter lip (closer to the body line) dives deeper but tighter. Steeper lip gives a wide, shallow, hunting action. Bassmaster: how deep can you go
      • Line tie and front area. Moving the tie toward the lip tip raises the running angle and makes the lure run shallower. Flume tests found steady diving when about 20–30% of the plan area sits ahead of the tie. Daida et al. 2001, tied-eye position
      • Line diameter. Thinner line has less drag, so the lure runs deeper. The towed-line model uses the line's diameter and the retrieve speed. Holt & Romanack test via Bassmaster (8 lb about 20% deeper than 14 lb)
      • Ballast and righting. Weight low and forward makes the lure self-right and steepens the dive. Weight in the spine adds roll and lowers blowout speed. Basic hydrostatics: the gap between centre of gravity and centre of buoyancy sets the righting moment.
      • Weight transfer. Balls slide to the tail for the cast, then roll forward on the retrieve. Used in the X-Rap and Megabass jerkbaits. Megabass LBO II
      • Hook size. Recommended hook sizes per length follow production jerkbaits and cranks. Hook drag and mass both damp the action.
      • Vortex shedding. Lip wake frequency uses a Strouhal number near 0.18. Soft tail beat uses about 0.3, the same range as swimming fish. Taylor, Nudds & Thomas 2003, Nature
      • Soft tail start-up. Tail kicks once water pressure on the paddle bends the tail bridge. That depends on material stiffness and bridge thickness. Soft silicone and plastisol kick at a slow wind; stiff printed TPU needs a fast retrieve. Dragon Skin 10 data sheet

      These are first-order models, independently audited and tuned against published depth ratings and builder tests. Trust the trends and the weights; treat wobble, roll and glide or topwater action numbers as guides until we have tank-test video of printed bodies.

      Signature Lures · Designer Rewards

      Design it. Catch on it. Earn 20%.

      Prove your design on the water and we list it in the Signature gallery under your name. Every time someone buys it, you earn 20% of the sale.

      What could your lure earn?

      Per sale
      A month
      A year

      20% of the price before VAT and postage. The price starts at the lure in your designer right now.

      1. 1Design itBuild your lure here. Every one has a 5 mm Smart Tag sealed in its head.
      2. 2Fish itBuy it, fish it and catch on it. That's the proof.
      3. 3Tap, film, verifiedTap your phone on the lure. The Catch app opens on your account and starts filming.
      4. 4Listed and earningWe check the clip, list your design under your name, and pay you 20% of every sale.

      A working mock-up of the Catch app. It uses the lure in your designer right now.

      Why a catch can't be faked

      • The tag proves the lure was there. Each Smart Tag is a 5 × 5 mm NXP NTAG 424 DNA chip sealed in the lure's head. Every tap creates a fresh code that only our server can check. A copied tag or a saved link fails.
      • Filmed in the app, right then. Recording starts within 60 seconds of the tap. No uploading old videos from your camera roll.
      • One continuous clip. Show the fish with the lure in its mouth or in the net. 10–20 seconds is plenty.
      • Works with no signal. The clip is locked on your phone with the tap code and time, then uploads when you're back in signal.
      • A person checks it. We review every catch before a design is listed.
      • Buyers do the rest. You only earn when other anglers buy your lure, so there's nothing to gain from a staged catch.

      Your spots stay yours

      We keep the exact location private and only ever show the area, like "River Foyle".

      Fish first

      Short clips mean catch-and-release fish go back quickly. The app reminds you.

      Signature gallery

      Examples of how listings will look. The pilot opens to local anglers, guides and tackle shops first.

      Examples, not real listings yet
      Designer Rewards terms draft, to be confirmed
      • What you earn: 20% of the price of each Signature sale of your design, before VAT and postage.
      • Which sales count: orders placed through your design's Signature listing, including small changes to colour, finish or length. A new shape or lip makes it a new design.
      • How long: for three years from listing, while the design stays listed.
      • Your own orders: buying your own design doesn't earn a commission.
      • Getting listed: a verified catch through the Catch app, approved by us. If two designs are near-identical, the first one verified gets the credit.
      • Payouts: monthly, once you've earned £20, by bank transfer or PayPal. You're responsible for declaring it; in the UK the first £1,000 a year is usually covered by the trading allowance.
      • Under 18s: need a parent or guardian to agree to the terms and receive payouts.
      • The design: you keep the credit. You give us a licence to make and sell it, and we set the build and safety standards because we make it. We can remove listings that break the rules, including staged catches.

      These are draft terms for the pilot and will be reviewed by a solicitor before launch.

      Got an idea you'd like us to develop with you instead? Angler Partnership

      Inside the lure

      See where the weight sits and where the wire runs.

      Switch the viewer to Inside and your own design is cut open. The ballast, wire, lattice and rattle all resize as you change the length, width, wall and buoyancy.

      Cutaway render of a jerkbait showing the through-wire, tungsten ballast, weight-transfer channel, rattle chamber and lattice
      1. Through-wire

        One stainless wire runs from the line tie at the nose, through the body, to the tail hook. The belly hook hanger is formed on the same wire, so if the body cracks the hooks and line tie stay connected. Traditional builders drill a wooden body for the wire; we print the channel into the body.

        Source: Lure Parts Online, making through-wire lures
      2. Tungsten ballast, low and forward

        Most floating and diving baits balance close to the front hook hanger, so weight placed there keeps the lure level, and weight in the belly turns a floater into a suspender or a sinker. That's why the simulator puts the tungsten low, just ahead of the first hanger.

        Source: Bassmaster, weighting hard baits
      3. Weight transfer (optional)

        Ballast balls run in a channel from the belly to the tail. On the backcast they roll to the tail so the lure flies tail-first and further. A magnet catches them back at the belly when the retrieve starts or on the first twitch, so the swimming balance isn't upset.

        Source: Wired2Fish, weight transfer systems
      4. Sealed rattle chamber

        Rattle balls sit in their own sealed cylinder, so the sound is consistent and the body stays watertight. Cutaways of commercial rattling crankbaits show the same approach: a fused plastic tube holding a steel ball.

        Source: TackleTour, rattling crankbait cutaway
      5. Wall and internal lattice

        The shell is printed 0.9 to 1.6 mm thick. Inside, an open lattice adds stiffness. When a lure needs more weight than the tungsten chamber holds, the lattice is printed denser instead.

        Our design rule, shown in the simulator
      6. Centre of gravity and buoyancy

        A lure stays upright when its centre of gravity (CG) sits below its centre of buoyancy (CB). How far forward or back the weight sits decides whether it rests level, nose-down or tail-down. The simulator estimates both from every part's weight and position.

        Calculated estimate, confirmed by tank test

      Shop All Lures

      Every design opens in the configurator, so you can change its size, weight, pattern and finish before you order.

      Not sure where to start? Pick your target species.

      How It Works

      From your idea to the water. A simple process designed for anglers.

      1. Choose a designStart from a proven body, or from the fish you're after.
      2. Customise your lureAdjust size, weight, colour and more.
      3. We manufacture itPrinted, ballasted, painted and assembled in our workshop.
      4. You fish with itA lure set up for your water and your fishing.
      Wireframe CAD model of a lure
      Design ItEvery body starts as an engineered CAD model.
      The same lure at three lengths
      Scale ItChange the length. Hardware and ballast follow the rules.
      A lure underwater
      Fish ItTell us how it swims. Reports shape the next revision.

      Angler Partnership

      Have an idea for a new lure?

      We work with anglers to develop, test and bring new designs to life, with the opportunity to earn a share of future sales.

      Concept sketch of a lure with dimensions
      Share your idea
      We develop and test it
      Launch together
      Earn a share of sales

      How the programme works

      1. You submit an ideaA sketch, a photo of a modified lure, a description or a 3D file.
      2. We review feasibilityCan it be printed, ballasted and rigged reliably? We'll tell you either way.
      3. CAD model and prototypeSuitable ideas are modelled and a first prototype is printed.
      4. Physical testingTank and field testing, often with you fishing the prototypes.
      5. Added to the rangeDesigns that perform are released and credited to you.
      6. Revenue shareYou receive an agreed percentage of future sales.

      Revenue share is agreed individually, in writing, before any design is commercialised. Submitting an idea doesn't commit you or us to anything.

      Submit Your Lure Idea

      Our Materials

      High-performance materials. A more sustainable future.

      We use engineered polymers, including recycled plastics where they do the job, to create durable, high-performance lures that stand up to real fishing conditions.

      Recycled polymer pellets in white, blue and black
      Recycled materialsDeclared per batch, with source
      Engineered for performanceImpact and soak tested
      Reduced wasteOn-demand manufacturing
      Longer service lifeReplaceable lips, tails, hardware
      MaterialUsed forWhyStatus
      PETG, engineering gradeHollow bodies, internal latticeTough, water resistant, holds fine detail. 1.27 g/cm³, used in every weight calculation.In use
      rPETG, recycledHollow bodies (option)Same density and print settings as PETG. Recycled content declared per batch with its source.In use
      Ocean-recovered polymer blendsSelected bodies, once qualifiedOnly where the source is traceable and the blend passes the same impact and soak tests.Under test
      PolycarbonateDiving lipsStiff and impact resistant, so the lip keeps its angle after hitting rock.In use
      TPU, flexibleSwimbait tails, interchangeable finsFlexible parts that move with the water and can be replaced on their own.Under test
      TungstenInternal ballast19.3 g/cm³, so small chambers give a low centre of gravity.In use
      Stainless wire, carbon-steel treblesThrough-wire, split rings, hooksThrough-wire construction keeps hooks attached even if a body cracks.In use

      Journal / Development Lab

      Behind the designs. Real testing. Continuous development.

      About Us

      “I sketched the first version of this idea about eight years ago, on the back of a job sheet.”

      Draft copy · edit in your own words before launch

      I'm an engineer from Derry. I spent 17 years in high-volume manufacturing, and part of that was introducing additive manufacturing to a factory floor. That taught me how quickly a good idea becomes a working part when you can print it, test it and change it the same week.

      I'm also an angler, and every angler knows the lure that's nearly right. A bit longer, a bit slower to sink, a different colour for coloured water. With injection moulding, nobody will make that for you unless thousands of other people want it too.

      3D printing changes that. We design each body properly in CAD, test it in the tank and on the water, then let you adjust the parts that are safe to adjust. We're not claiming our lures catch more fish than anyone else's. We're offering lures you have a hand in designing.

      Mechanical & electrical engineeringComposites & polymersWorkshop in Derry, Northern Ireland

      Workshop view · staff only

      Every order carries its exact build record.

      Orders arrive with the model ID, revision, dimensions, ballast, hardware and finish needed to make that lure. Place a test order from the basket and it appears here.

      OrderLureTargetEst.Stage

      Build record

      select an order
      Select an order to see its manufacturing record.

      Contact and Support

      Questions about an order, a design or a material?

      Use the form or email us. Lure ideas go through the Angler Partnership form so files stay with the submission.

      hello@3dprintedfishinglures.com

      Suggested address · set up before launch